Home > Frigidaire Affinity > How To Reset Frigidaire Affinity Washer

How To Reset Frigidaire Affinity Washer

Contents

To recall an error code: • Wake the machine by pressing any button • Wait 5 seconds • Press and hold the Start and Pause Cancel buttons simultaneously • All LED's Door lock/switch assembly, Wiring harness E52 Bad signal from the motor tachometer Unplug the washer. See the schematic below:If that is not enough, then the drain pump access is located in the front side of the machine, hidden behind the trim at the base. will be open when lid openIF it does turn out that the lid lock is the problem the part number for it is 134101800it could be purchased online at;repairclinic.comapdepot.comapwagner.comsearspartsdirect.commidwestapplianceparts.comIf the switch http://kshelper.com/frigidaire-affinity/frigidaire-washer-reset-code.html

Perhaps because it's from Lowes?) Then, if it's likely the cause, I'd like to find out how to get it and install. Test any switches on the door lock with an Ohm meter. Drive motor, Outer tub, Spin basket, Speed control board E5A Speed control board is overheated Replace the speed control board. Water-level pressure sensor, Water inlet valve assembly E43 Control board failure Unplug the washer for 5 minutes.

How To Reset Frigidaire Affinity Washer

Copyright © 2000-2016 ApplianceAid.com. Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

LinkBack LinkBack URL About LinkBacks Bookmark & Share Digg this Thread! Turn the program knob (6) clicks from the start position. on a small number of washers with serial number prefix XC4, if the previous procedure does not perform as specified, follow the option below: • Follow all previous steps but instead

I was around and quickly freed the button. The kick panel is held to the washer's frame by screws:After removing the panel you will Be able to access the pump. Exit Diagnostic Mode to return the washer to normal operation. Frigidaire Affinity Washer Clear Error Codes Points valid for 14 days.

The door lock solenoid will deactivate and the loading door can be opened. By reading any content on this site you agree to AppliancePartsPros.com , Inc. Shop the largest selection of Plus Size Costumes online! Spin the motor pulley.

Refertotest(9)E57 Highcurrentoninverter. Frigidaire Affinity Washer Error Code E41 Example: E14. Drain pump EF2 Too much suds Reduce the amount of high-efficiency (HE) high-efficiency detergent being used in the washer. Lid Switch Assembly If the washer won't drain the lid switch assembly might be defective.

Frigidaire Front Load Washer Keeps Beeping

Full Answer > Filed Under: Washers & Dryers Q: How can you identify an error code on a Bosch washer? I have unplug the machine for more than 3 mins but no luck. How To Reset Frigidaire Affinity Washer Test any switches on the door lock with an Ohm meter. Frigidaire Gallery Series Washer Error Codes Coin Trap If the washer won't drain the coin trap may be clogged.

Check the resistance through the tachometer on the motor. this contact form Refer totest (3).E23 Drainpumprelayoncontrolboardfailed. The code is obtained by counting the number of times the lights flash. S.E., Cleveland, TN 37311 Legal Notice|Privacy Notice©1999 - 2012Appliance Parts Pros.com®. Frigidaire Washer Won't Stop Beeping

The error code remains stored in the control but once the problem is corrected, it does not effect the operation of the washer. E47 Board thinks the door PTC circuit is open in spin. The control will signal the last error code. have a peek here If it doesn't spin freely, replace the drive motor.

Expert: Chas replied7 years ago. Frigidaire Affinity Washer Diagnostic Mode Normally, the coin trap can be accessed through an access panel. The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common).

Reply With Quote September 3rd, 2013,09:47 AM #3 bpalmer999 View Profile View Forum Posts Premium Member Join Date Jun 2013 Location kentucky Posts 7 A couple of updates.

If it does, replace the electronic control board. Order Appliance Parts with 365-Day Hassle Free Return Policy - AppliancePartsPros.com #5 (permalink) 04-11-2012, 06:32 AM DavidPJ Junior Member Join Date: Apr 2012 Posts: 4 Thanks Gene. Refertotest(8)E56 Highmotorcurrent. Frigidaire Affinity Error Codes Dryer If the wiring connections are sound, the water level pressure sensor usually needs to be replaced.

STILL WON'T AGITATE please show me a diagram Jun 14, 2011 | Whirlpool LSR7333 Top Load Washer Not finding what you are looking for? In the morning all 10/15/2016 10/15/2016 smitty1486 Trying to figure out what the likely underlying problem for 10/15/2016 10/15/2016 smitty1486 Whirlpool gi7fvcxwa.. Set of four chrome drip pans, 2 small, 2 large Item Number W10278125

Thanksgiving is coming - Item # W10278125 RepairClinic.com also ships appliance repair parts to Canada!....to your home, Check This Out Electronic control board E75 Failed water temperature sensor circuit This error code is for washers with a digital display only.

Should a malfunction occur, the keypad will flash a series o... The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). Drain Pump If the washer won't drain water the drain pump might be defective. To start viewing messages, select the forum that you want to visit from the selection below.

Discount will be automatically applied during check-out. Top Frigidaire Washing Machines Experts Electrolux Level 3 Expert 4342 Answers Richard Roth Level 3 Expert 9472 Answers Dan Webster Level 3 Expert 8147 Answers Are you a Frigidaire Washing Machine Find the model of Frigidaire washer experiencing the problem by entering the model number into the search box or clicking on the browse by product category link. Q: What does it mean when your dryer does not heat up?

There may be something preventing the pump from draining in the Pump filter. If the drain pump is damaged, replace it. Here are the breakdown diagrams and Replacement parts for Frigidaire GLTF2940ES3 Frigidaire/washer | AppliancePartsPros.com Gene. __________________ Appliance Repair Expert in Orange County, California. Full Answer If no user manual is available, an error code can be diagnosed on the official Frigidaire website.

If this code would appear on a washer in the Good model line, the five indicator lights would blink fifteen times and the START indicator light would blink once. I received the the codes when I flipped from the home position to the next one. Drive Belt If the washer won't drain, should check the drive belt. The switches should have continuity according to their design.

Be sure the hose did not get kinked behind the washer. A: You can identify a Bosch washer error code on the keypad which is used to control the machine. Frigidaire Frontload Washer New Fault Codes Model differences: Better models have a digital readout display Good models do not have a digital readout display In the Better Models line, the failure Q: Has Maytag announced a washer recall?

If the failure is something that the customer can correct (such as the water faucets being turned off), the washer will operate normally the next time it is started.