Home > Frigidaire Oven > Frigidaire Oven F11 Error Code

Frigidaire Oven F11 Error Code


If open, replace Lock Motor Assembly. 5. (F90, 91, 92, 93 & 94) Lock Motor continuously runs - if Micro Switch is open, replace Lock Motor Assembly. 6. (F92, 93 & Press CANCEL to reject the change if necessary." If the temperature is out of range for more than 35°F, it can not be adjusted. Thank you, Gene. MML // Mar 31, 2015 at 4:09 pm Hi Gene, Thanks so much for your reply. Source

Or do you think there may be more to the problem? Thanks, please let me know and I'll place an order. The part number you posted is for the panel which has nothing to do with this problem. Thanks in advance!

Frigidaire Oven F11 Error Code

Gene. I do have several boards. This is the opposite of most thermistors we use in other appliances, but the concept is the same. In order to access it you would need to remove the oven from the cabinet.

model plgf389cce Frigidaire professional series Gene // May 17, 2015 at 6:34 pm Hello Greg. You may want to order a new overlay if you would not be able to move the old one to the new EOC. Ed Gene // Apr 24, 2015 at 8:27 pm Hello Ed, You may want just to replace the wires from the temperature probe to the EOC. Frigidaire Stove Error Codes F7 Thanks, Ehsan.

Thank you Gene // Mar 7, 2015 at 2:42 pm Hello Frank. After much reserach I purchased a new EOC part # 316462861 which arrived today and I immediately installed it. If the reading is incorrect and the wires and plugs between the sensor and the EOC are good, replace the temperature sensor (RTD probe). The part number for the EOC is 316418521 Good luck.

ft. Frigidaire Oven F10 Reset I washed the surface of the stove earlier today and when I turned the oven on it shot a flame out where the heat and condensation come out on top. Gene. I get a f10 error code only on the top oven.

Frigidaire Oven Error Code F30

The user interface board is mounted on the back of the range, just below the control panel. If the reading is incorrect and the wires and plugs between the sensor and the EOC are good, replace the temperature sensor (RTD probe). Frigidaire Oven F11 Error Code The correction for this problem is to replace the EOC. Frigidaire Oven F10 Error Thanks so much Jacqui Gene // Jan 4, 2015 at 11:59 am Hello Jacqui, My answer is Yes.

Otherwise if the wire harnesses are good, the user interface board would need to be replaced. http://kshelper.com/frigidaire-oven/frigidaire-oven-f1-error.html Keep me posted. This happens every time and we have used different oven thermometers in case one was defective. Check the upper oven temperature sensor by measuring resistance between two wires connected to the pin 9 and 10 at the plug P27. Frigidaire Eoc

Shorted Probe connection. 1. (F30 or F31) Check resistance at room temperature & compare to **RTD Sensor resistance chart. The F11 error code means that control has sensed a shorted keypad. Gene. http://kshelper.com/frigidaire-oven/f3-error-code-on-frigidaire-oven.html Did the motor run or not?

IMPORTANT DISCLAIMER: The Author of this web site assumes no responsibility for inconveniences or damages resulting from use of the information he supplies. Frigidaire Oven F10 Beeping I would recommend to eliminate the sensor plug and splice the sensor into the wire harness using a high temperature wire nuts. Codes flashing are F 7 and 20.

Happy holidays to you and your loved one as well!

Could you please explain what this is. Eric Ehsan Rehman // Jan 10, 2015 at 6:00 pm Hello Gene, We have a Frigidaire Oven, model # FGFLZ87GCA. I would not tell them it happened due to bad weather. What Does F10 Mean On A Frigidaire Oven Wire nuts (pack of 10) AP5641944 Good luck and keep us posted.

Repairclinic.com Appliance Newsletters Purchase Info for Appliance Parts & Manuals » Need Parts? I checked and reset the breaker only to have the oven (316233850) alarmed and locked the door like it was going into the clean. Mike Gene // Jun 6, 2015 at 10:30 pm Hello Mike, Thank you for your question. Check This Out Gene // Jan 12, 2015 at 11:11 pm Hello Ehsan, F11 error code means a shorted key in the keypad.

Contact the seller and request the replacement. James // Dec 21, 2014 at 11:14 am hi Gene i have a frigidaire stove that is showing an f11 code. Rachel // Mar 14, 2015 at 8:14 am Hello, My range is showing F10 error code since this morning. Gene.

Check Sensor wiring harness between EOC & Sensor Probe connector. 2. (F30 or F31) Check resistance at room temperature, if less than 500 ohms, replace **RTD Sensor Probe. In such situation the solution is to replace the Electronic Oven Control (EOC). Any suggestion is highly appreciated. Gene // May 10, 2015 at 9:44 pm Hello Sally, I'm sorry for the delay.

Oven temperature sensor probe F9 Errors for Frigidaire Self-Cleaning Ranges Error Code Condition Check/Repair Shop Parts F9 The electronic oven control board has detected a problem with the oven door latch Such special considerations include installation parameters, installation location, the possibility of manufacturing or construction defects, damage in transit and others. she gets error code 11. The part number for EOC is 316557115 You may want to replace the overlay as well because the old one can be easy damaged.

You can use an universal flat oven igniter, made by GE. Also the broiler coil came on but the unit was not in broil but bake. Washer Parts  ·  Dryer Parts  ·  Refrigerator Parts  ·  Dishwasher Parts  ·  Range & Oven Parts  ·  More  Print Register to comment on this topic Pages: [1] 2 Go Up « previous next » ApplianceJunk.com » Forum Index » Range, Oven Close Chat is currently unavailable We're sorry!

Check wiring of lock motor, lock switch and door switch circuits. The clock turns on but will not allw me to adjust it and once again the broiler automatically turned on however this time the screen flassed the F11 error. The EOC part number is 316418708 You can order it by clicking on the part number.