Home > Frigidaire Oven > What Does F3 Mean On A Frigidaire Oven

What Does F3 Mean On A Frigidaire Oven

Contents

Gene. Gene. The display read F3, I tried the 'CANCEL' button, it stopped for a minute then started beeping and the display now reads F2. In this range there are no a separate keypad. Source

My wife is suspicious of the temperature, however. Also the model number you posted is incomplete. The electronic oven control board registers the condition as a runaway oven. Most likely the problem is a faulty EOC.

What Does F3 Mean On A Frigidaire Oven

Freestanding ... All rights reserved. © Applianceblog.com 2004 - 2014 Overnight or Rapid Shipping available to your home or office! model #GLEF378ABC. The part number for the EOC is 316455410 Good luck.

Keep me posted. Anmelden 6 Wird geladen... Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual 50385155-434c-467c-aabc-0a989e4fbb16.p... Frigidaire Electronic Oven Control skip navigation Click to call Click to Chat 1-800-491-3457 Login Register Order Status Feedback Get Manuals Repair Help Expert Q & A Recently Viewed My Models (0) Main Menu Recently Viewed

If you ordered the EOC and the temperature sensor from AppliancePartsPros. Frigidaire Oven F1 Error Gene. If the reading at the sensor is the same as reading at the EOC plug, the sensor is defective. Top #277383 - 05/15/06 07:07 PM Re: Frigidaire oven error codes F3 & F2 [Re: jeff1] rdamuth newbie Registered: 05/15/06 Posts: 3 I believe that it is a REG74BL3.The EOC sounds

It is located behind the control panel. Frigidaire Self Cleaning Oven F1 Error darlene // Dec 19, 2014 at 7:03 pm The frigidaire stove my son has has a f10 code. Ken // Dec 28, 2014 at 1:36 pm Hello Gene, Thank you for the info.. George sharon // Jan 1, 2015 at 10:09 pm i have a frigidaire model fgef301dnb.

Frigidaire Oven F1 Error

Last night I tried to use the oven and it started flashing a F30 error. Gene // Jan 4, 2015 at 1:07 pm Hello Eric, If the problem just melted wire harness connector and the temperature probe tests out OK then the easiest solution is to What Does F3 Mean On A Frigidaire Oven Otherwise the EOC is the culprit and would need to be replaced. Frigidaire Microwave F3 Error Code All Electronic Oven Controls (EOC) have ability for self diagnosis.

Gene. this contact form FGGF3076KBK. sensor??? If the reading is incorrect, remove the sensor from the oven and check its resistance at the sensor. Frigidaire Oven Temperature Sensor

Check oven temperature sensor. How do you adjust the oven door on a Fridgedaire Gallery Series gas stove? The part number for the EOC is 316557115 The part number for the white overlay is 316419104 Good luck. have a peek here When replacing a potentiometer, do not over-tighten the hex nut.

If there is nothing wrong and the sensor resistance is correct, replace the EOC. - The EOC Part number: AP2127074 Here are the breakdown diagrams and Replacement parts for FRIGIDAIRE FEB30S5ABA Frigidaire Oven Keeps Beeping F1 Thank you! I had noticed the same thing earlier in the day while baking chicken but no code came up at that time.

Frigidaire incorporated keypad into the electronic control board for most of the models and used just a faceplate or overlay which is adhered to electronic control board.

Could you please explain what this is. Sometimes while the oven is on but most of the time while the oven is cooling off. Any clue?? Frigidaire Oven F2 Error Code Keep me posted.

Frigidaire professional series FGFLMC55GCC The broiler automatically turns on by itself and I cannot turn it off without unplugging it. It is a lot of money but the worst part of it is that usually manufacturers will stop to make them in a few years after they made such model. Thank you for your question. Check This Out Hi gene- I have a runnaway temp issue.

The fan motor does work. When I used the oven the next day to heat taco shells, it got really hot (burnt them to chars!) and then the F10 code went off again- this time I You also may want to do the following troubleshooting: Unplug the range. What are your thoughts?

You may want to start the troubleshooting from testing the temperature probe resistance. No doubt about it and a new one would fix the problem. I managed to push them back into the cap, and we were able to reconnect it to the EOC board, but at least one of them broke off. Jeff // Jul 17, 2015 at 3:03 pm Sorry I forgot to tell you the problem came after a power surge and the only operations that work on the oven are

that's the part located in the oven. Thank you for your question. Capital Cooking... The black potentiometer should have a resistance of 10KΩ (± 10%).

The temperature may be increased as much as 35°F (19°C). 4. Gene. If you register, you may post in any forum and use of CAPTCHA code is not required. Mike // Jun 6, 2015 at 7:05 pm Hi Gene, I have a PLES389ECE showing F30.

If the reading is correct, test operation of the potentiometer by measuring the resistance between pin terminal G (center) and either of the outside pin terminals as the control shaft is LinkBack Thread Tools Search this Thread Display Modes #1 (permalink) 02-08-2010, 08:38 AM k75super Junior Member Join Date: Feb 2010 Posts: 3 F3 error code on Frigidaire oven The part number for the EOC is 316418720 You can order the part by clicking on the part number.